TI公司的drv8305-Q1是三相马达驱动的栅极驱动集成电路,提供三个高精度半桥驱动器,每个可驱动高边和低边N-MOSFET,电荷泵驱动器支持100%占空比,满足汽车应用的AEC-Q100规范,4.4V-45V工作电压,峰值栅极驱动电流1.25A和1A,主要用在三相BLDC和PMSM马达,汽车油泵和水泵,汽车风扇和鼓风机.本文介绍了DRV8305-Q1主要特性,框图,典型应用电路以及汽车两轴电动座椅驱动参考设计TIDA-01330主要特性,框图,电路图,材料清单和PCB设计图.

　　The DRV8305-Q1 device is a gate driver IC for threephasemotor-drive applications. The device providesthree high-accuracy half-bridge drivers, each capableof driving a high-side and low-side N-channelMOSFET. A charge pump driver supports 100% dutycycle and low-voltage operation for cold cranksituations. The device can tolerate load dumpvoltages up to 45-V.

　　The DRV8305-Q1 device includes three bidirectionalcurrent-shunt amplifiers for accurate low-side currentmeasurements that support variable gain settings andan adjustable offset reference.

　　The DRV8305-Q1 device has an integrated voltageregulator to support an MCU or other system powerrequirements. The voltage regulator can be interfaceddirectly with a LIN physical interface to allow lowsystemstandby and sleep currents.

　　The gate driver uses automatic handshaking whenswitching to prevent current shoot through. The VDSof both the high-side and low-side MOSFETs isaccurately sensed to protect the external MOSFETsfrom overcurrent conditions. The SPI providesdetailed fault reporting, diagnostics, and deviceconfigurations such as gain options for the currentshunt amplifier, individual MOSFET overcurrentdetection, and gate-drive slew-rate control.

　　DRV8305-Q1主要特性:

　　1• AEC-Q100 Qualified for Automotive Applications

　　• Ambient Operating Temperature Ranges:

　　– Temperature Grade 0 (E): –40℃ to 150℃

　　– Temperature Grade 1 (Q): –40℃ to 125℃

　　• 4.4-V to 45-V Operating Voltage

　　• 1.25-A and 1-A Peak Gate Drive Currents

　　• Smart Gate Drive Architecture (IDRIVE &TDRIVE)

　　• Programmable High- and Low-Side Slew-RateControl

　　• Charge-Pump Gate Driver for 100% Duty Cycle

　　• Three Integrated Current-Shunt Amplifiers

　　• Integrated 50-mA LDO (3.3-V and 5-V Option)

　　• 3-PWM or 6-PWM Input Control up to 200 kHz

　　• Single PWM-Mode Commutation Capability

　　• Serial Peripheral Interface (SPI) for DeviceSettings and Fault Reporting

　　• Thermally-Enhanced 48-Pin HTQFP

　　• Protection Features:

　　– Fault Diagnostics and MCU Watchdog

　　– Programmable Dead-Time Control

　　– MOSFET Shoot-Through Prevention

　　– MOSFET VDS Overcurrent Monitors

　　– Gate-Driver Fault Detection

　　– Reverse Battery-Protection Support

　　– Limp Home-Mode Support

　　– Overtemperature Warning and Shutdown

　　DRV8305-Q1应用:

　　• Three-Phase BLDC and PMSM Motors

　　• Automotive Fuel and Water Pumps

　　• Automotive Fans and Blowers

　　图1.DRV8305-Q1框图

　　图2.DRV8305-Q1典型应用电路

　　汽车两轴电动座椅驱动参考设计TIDA-01330

　　The TIDA-01330 design implements the drive circuitsfor two independent brushed DC motors. It provides asolution for automotive power seats with a highlyintegratedtwo-axis driver, reducing the overall bill ofmaterials. The interface to a simple microcontrollerIllustrates how the design reduces the processingburden on the control software.

　　In addition to the drive circuit for two motors, this TIDesign also includes current feedback sense circuitsand other diagnostic features to ensure reliableoperation and detection of faults. Additionally thecontrol circuit for an LED illumination element isimplemented, as well as the feasibility of providingtactile feedback to the seat occupant by vibrating ineither axis.

　　参考设计TIDA-01330主要特性:

　　• Drives Two Independent Brushed DC Motors

　　• Up to 10-A Motor Current (Each Axis)

　　• Current Feedback on Each Axis

　　• Reverse Battery Protection

　　• Low-Pass Filtering on Battery Power

　　• Drives LED for Floor Illumination

　　• Simple Microcontroller Interface

　　• Reduced Bill of Materials

　　参考设计TIDA-01330应用:

　　• Power Seat Height and Forward and BackwardAdjustment

　　• Power Seat Back Recline Adjustment andPower Fold

　　• Other Two-Axis Brushed DC Motor Drives

　　图3.参考设计TIDA-01330外形图

　　参考设计TIDA-01330主要指标:

　　图4.参考设计TIDA-01330框图

　　图5.参考设计TIDA-01330扩展到五轴应用图

　　图6.参考设计TIDA-01330电路图

　　参考设计TIDA-01330材料清单:

　　图7.参考设计TIDA-01330 PCB设计图(1)

　　图8.参考设计TIDA-01330 PCB设计图(2)

　　图9.参考设计TIDA-01330 PCB设计图(3)

　　图10.参考设计TIDA-01330 PCB设计图(4)

　　图11.参考设计TIDA-01330 PCB设计图(5)

　　图12.参考设计TIDA-01330 PCB设计图(6)

　　图13.参考设计TIDA-01330 PCB设计图(7)

　　图14.参考设计TIDA-01330 PCB设计图(8)

　　图15.参考设计TIDA-01330 PCB设计图(9)

　　德州仪器(Texas Instruments)，简称TI，是全球领先的半导体公司，为现实世界的信号处理提供创新的数字信号处理(DSP)及模拟器件技术。除半导体业务外，还提供包括传感与控制、教育产品和数字光源处理解决方案。TI总部位于美国德克萨斯州的达拉斯，并在25多个国家设有制造、设计或销售机构。

　　德州仪器 (TI) 是全球领先的数字信号处理与模拟技术半导体供应商，亦是推动因特网时代不断发展的半导体引擎。

　　----作为实时技术的领导者，TI正在快速发展，在无线与宽带接入等大型市场及数码相机和数字音频等新兴市场方面，TI凭借性能卓越的半导体解决方案不断推动着因特网时代前进的步伐!

　　----TI预想未来世界的方方面面都渗透着 TI 产品的点点滴滴，您的每个电话、每次上网、拍的每张照片、听的每首歌都来自 TI数字信号处理器(DSP) 及模拟技术的神奇力量。

　　2011年4月5日，德州仪器(TI)和美国国家半导体(NS)宣布签署合并协议，TI将以25美元/股、总额约65亿美元的现金价格，收购国家半导体。本次收购将使业界共同致力于解决客户模拟问题的两个领导者实现强强联手。

　　德州仪器也是图形计算器的重要生产商，其生产的TI 图形计算器系列享誉全球。

　　详情请见:

tidrpz5.pdf

drv8305-q1.pdf

tidrpz7.pdf

tidrpz4.pdf

tiducm0.pdf