ADI的ADM3065E是3.0V-5.5VIEC静电放电(ESD)保护RS-485收发器解决方案
The ADM3065E is a 3.0 V to 5.5 V, IEC electrostatic discharge (ESD) protected RS-485 transceiver, allowing the device to withstand ±12 kV contact discharges on the transceiver bus pins without latch-up or damage. The ADM3066E features a VIO logic supply pin allowing a flexible digital interface capable of operating as low as 1.62 V.
The ADM3065E/ADM3066E are suitable for high speed, 50 Mbps, bidirectional data communication on multipoint bus transmission lines. The ADM3065E/ADM3066E feature a ¼ unit load input impedance, which allows up to 128 transceivers on a bus.
The ADM3065E/ADM3066E are half-duplex RS-485 transceivers, fully compliant to the Profibus® standard with increased 2.1 V bus differential voltage at VCC ≥ 4.5 V.
The RS-485 transceivers are available in a number of space-saving packages, such as a 10-lead, 3 mm × 3 mm LFCSP package, an 8-lead, 3 mm × 3 mm MSOP package, a 10-lead, 3 mm × 3 mm MSOP package, and an 8-lead, narrow body SOIC package. Models with operating temperature ranges of −40℃ to +125℃ and −40℃ to +85℃ are available.
Excessive power dissipation caused by bus contention or by output shorting is prevented by a thermal shutdown circuit. If, during fault conditions, a significant temperature increase is detected in the internal driver circuitry, this feature forces the driver output into a high impedance state.
The ADM3065E/ADM3066E guarantee a logic high receiver output when the receiver inputs are shorted, open, or connected to a terminated transmission line with all drivers disabled.
ADM3065E/ADM3066E主要特性:
TIA/EIA RS-485 compliant over full supply range
3.0 V to 5.5 V operating voltage range on VCC
1.62 V to 5.5 V VIO logic supply
ESD protection on the bus pins
IEC 61000-4-2 ≥ ±12 kV contact discharge
IEC 61000-4-2 ≥ ±12 kV air discharge
HBM ≥ ±30 kV
Full hot swap support (glitch free power-up/power-down)
High speed 50 Mbps data rate
Full receiver short circuit, open circuit, and bus idle fail-safe
Extended temperature range up to 125℃
Profibus compliant at VCC ≥ 4.5 V
Half duplex
Allows connection of up to 128 nodes onto the bus
Space-saving package options
10-lead 3 mm × 3 mm LFCSP package
8-lead and 10-lead MSOP packages
ADM3065E应用:
Industrial fieldbuses
Process control
Building automation
Profibus networks
Motor control servo drives and encoders
图1.ADM3066E功能框图
图2.ADM3065E功能框图
图2.ADM3065E半双工RS-485通信网络框图
图3.ADM3065E信号和电源隔离25Mbps RS-485解决方案(简化框图)
评估板EVAL-ADM3065EEBZ和EVAL-ADM3065EEB1Z
The EVAL-ADM3065EEBZ and EVAL-ADM3065EEB1Z allow quick and easy evaluation of the ADM3065E 50 Mbps RS-485 transceiver with standard SOIC and MSOP footprints respectively. The evaluation boards allow the input and output functions to be exercised without external components. Screw terminal blocks provide convenient connections for power and ground, digital input and output, and RS-485 signals. The evaluation boards can be powered by a standard configurable bench power supply within a 3 V to 5 V range.
The EVAL-ADM3065EEBZ evaluation board has a footprint for the ADM3065EBRZ half duplex RS-485 transceiver in an 8-lead SOIC package. The EVAL-ADM3065EEB1Z evaluation board has a footprint for a full duplex RS-485 transceiver in an 8-lead MSOP package.
Complete specifications for the ADM3065E device are provided in the ADM3065E data sheet and should be consulted in conjunction with this user guide when using the evaluation board.
评估板EVAL-ADM3065EEBZ和EVAL-ADM3065EEB1Z主要特性:
Easy evaluation of ADM3065E 50 Mbps RS-485 transceiver
Board layouts for standard half duplex RS-485 footprints
8-lead, SOIC, ADM3065EBRZ (EVAL-ADM3065EEBZ)
8-lead, MSOP, ADM3065EBRMZ (EVAL-ADM3065EEB1Z)
Power/ground connections through screw terminal block
3.0 V to 5.5 V operating voltage range on VCC
IEC ESD protection on the RS-485 A and B bus pins
±12 kV contact discharge and ±12 kV air gap discharge
Screw terminal blocks for logic input/output and RS-485 signals
Jumper-selectable enable/disable for RE and DE
Test points for measuring all signals
Resistors and footprints for termination and biasing networks
EVALUATION KIT CONTENTS
EVAL-ADM3065EEBZ or EVAL-ADM3065EEB1Z
ADDITIONAL EQUIPMENT NEEDED
Oscilloscope
Signal generator or UART
3 V to 5 V supply
图4.评估板EVAL-ADM3065EEBZ外形图
图5.评估板EVAL-ADM3065EEB1Z外形图
图6.半双工RS-485两板点对点测试图
图7.评估板EVAL-ADM3065EEBZ电路图
图8.评估板EVAL-ADM3065EEB1Z电路图
评估板EVAL-ADM3065EEBZ材料清单:
评估板EVAL-ADM3065EEB1Z材料清单:
图9.评估板EVAL-ADM3065EEBZ/EVAL-ADM3065EEB1Z PCB丝印图
图10.评估板EVAL-ADM3065EEBZ/EVAL-ADM3065EEB1Z PCB元件边/层1
图11.评估板EVAL-ADM3065EEBZ/EVAL-ADM3065EEB1Z PCB层2
图12.评估板EVAL-ADM3065EEBZ/EVAL-ADM3065EEB1Z PCB层3
图13.评估板EVAL-ADM3065EEBZ/EVAL-ADM3065EEB1Z PCB层4
Analog Devices, Inc.(简称ADI)。中国注册公司名字为“亚德诺半导体技术(上海)有限公司。美国纳斯达克上市公司 (NASDAQ代码: ADI)。
将创新、业绩和卓越作为企业的文化支柱,并基此成长为该技术领域最持久高速增长的企业之一。ADI公司是业界认可的数据转换和信号处理技术全球领先的供应商,拥有遍布世界各地的60,000客户,涵盖了全部类型的电子设备制造商。作为领先业界40多年的高性能模拟集成电路(IC)制造商,ADI的产品用于模拟信号和数字信号处理领域。
公司总部设在美国马萨诸塞州诺伍德市,设计和制造基地遍布全球。ADI公司被纳入标准普尔500指数(S&P 500 Index)。
Analog Devices, Inc.(简称ADI)。中国注册公司名字为“亚德诺半导体技术(上海)有限公司。美国纳斯达克上市公司 (NASDAQ代码: ADI)。
将创新、业绩和卓越作为企业的文化支柱,并基此成长为该技术领域最持久高速增长的企业之一。ADI公司是业界认可的数据转换和信号处理技术全球领先的供应商,拥有遍布世界各地的60,000客户,涵盖了全部类型的电子设备制造商。作为领先业界40多年的高性能模拟集成电路(IC)制造商,ADI的产品用于模拟信号和数字信号处理领域。
公司总部设在美国马萨诸塞州诺伍德市,设计和制造基地遍布全球。ADI公司被纳入标准普尔500指数(S&P 500 Index)。
详情请见:
责任编辑:Davia
【免责声明】
1、本文内容、数据、图表等来源于网络引用或其他公开资料,版权归属原作者、原发表出处。若版权所有方对本文的引用持有异议,请联系拍明芯城(marketing@iczoom.com),本方将及时处理。
2、本文的引用仅供读者交流学习使用,不涉及商业目的。
3、本文内容仅代表作者观点,拍明芯城不对内容的准确性、可靠性或完整性提供明示或暗示的保证。读者阅读本文后做出的决定或行为,是基于自主意愿和独立判断做出的,请读者明确相关结果。
4、如需转载本方拥有版权的文章,请联系拍明芯城(marketing@iczoom.com)注明“转载原因”。未经允许私自转载拍明芯城将保留追究其法律责任的权利。
拍明芯城拥有对此声明的最终解释权。