Renesas公司的RX24U是功能强大的内置了差分放大器和安全系统的32位马达控制mcu,工作频率80MHz,集成了浮点单元(FPU),153.6 DMIPS性能,12位ADC,80MHz PWM,512-/384-/256KB代码闪存,8KB数据闪存和32KB SRAM,工作电压2.7V- 5.5V,主要用在通用工业和消费类设备.本文介绍了RX24U主要特性和指标,框图,以及RX24U开发板RSK主要特性和指标,内部框图,元件布局图,调试连接图和电路图.

　　The RX24U Group features a 32-bit microcontroller ideally suited for dual inverter control with a built-in Floating-Point Unit (FPU) that enables it to easily execute complex inverter control algorithms. The built-in Differential Programmable Gain Amplifier and the provide safety system allow to bring application system cost down.

　　The easy usability of the RX24U is helping our customers to reduce the time to market by reducing software development efforts and system design by providing a ready-to-go motor control solution, including software and hardware design examples.

　　RX24U主要特性:

　　■ 32-bit RXv2 CPU core

　　• Max.operating frequency:80 MHzCapable of 153.6 DMIPS in operation at 80 MHz

　　• Enhanced DSP: 32-bit multiply-accumulate and 16-bitmultiply-subtract instructions supported

　　• Built-in FPU: 32-bit single-precision floating point(compliant to IEEE754)

　　• Divider (fastest instruction execution takes two CPU clockcycles)

　　• Fast interrupt

　　• CISC Harvard architecture with 5-stage pipeline

　　• Variable-length instructions, ultra-compact code

　　• On-chip debugging circuit

　　• Memory protection unit (MPU) supported

　　■ Low power design and architecture

　　• Operation from a single 2.7-V to 5.5-V supply

　　• Three low power consumption modes

　　■ On-chip code flash memory

　　• 512-/384-/256-Kbyte capacities

　　• On-board or off-board user programming

　　• For instructions and operands

　　■ On-chip data flash memory

　　• 8-Kbyte (Number of erase/write cycles: 1,000,000 (typ))

　　• BGO (Back Ground Operation)

　　■ On-chip SRAM, no wait states

　　• 32 Kbytes of SRAM

　　■ Data transfer functions

　　• DTC: Four transfer modes

　　■ Reset and supply management

　　• Seven types of reset, including the power-on reset (POR)

　　• Low voltage detection (LVD) with voltage settings

　　■ Clock functions

　　• Main clock oscillator frequency: 1 to 20 MHz

　　• External clock input frequency: Up to 20 MHz

　　• PLL circuit input: 4 MHz to 12.5 MHz

　　• On-chip low-speed oscillators, on-chip high-speedoscillators, dedicated on-chip oscillator for the IWDT

　　• Clock frequency accuracy measurement circuit (CAC)

　　■ Independent watchdog timer

　　• 15-kHz on-chip oscillator produces a dedicated clocksignal to drive IWDT operation.

　　■ Useful functions for IEC60730 compliance

　　• Self-diagnostic and disconnection-detection assistancefunctions for the A/D converter, clock frequency accuracymeasurement circuit, independent watchdog timer, RAMtest assistance functions using the DOC, etc.

　　■ MPC

　　• Multiple locations are selectable for I/O pins of peripheral functions

　　■ Up to 9 communications channels

　　• CAN (compliant with ISO11898-1), incorporating 16message boxes (1 channel)

　　• SCI with many useful functions (6 channels)

　　Asynchronous mode, clock synchronous mode, smart cardinterface mode, simplified SPI, simplified I2C, andextended serial mode.

　　• I2C bus interface: Transfer at up to 400 kbps, capable ofSMBus operation (1 channel)

　　• RSPI capable of high speed connection Transfer at up to 20Mbps (1 channel)

　　■ Up to 25 extended-function timers

　　(Up to three-phase complementary PWM3-channel simultaneous output)

　　• 16-bit MTU3: 80 MHz operation, input capture, outputcompare, three-phase complementary PWM × 2 channelsoutput, CPU-efficient complementary PWM, phase

　　counting mode (nine channels)

　　• 16-bit GPT: 80 MHz operation, input capture, outputcompare, PWM wave-form single-phase complementary ×

　　4 channels output or three-phase complementary ×1 channel + single-phase complementary × 1 channel

　　output, comparator interlocking operation (Countoperation, PWM negate control) (4 channels)

　　• 8-bit TMRs (8 channels)

　　• 16-bit compare-match timers (4 channels)

　　■ 12-bit A/D converter: 22 channels in 3 units

　　• Incorporating sample-and-hold circuit 12 bits × 3 units(unit 0: 5 channels, unit 1: 5 channels, unit 2: 12 channels)

　　• Sampling time can be set for each channel

　　• Group scan priority control mode (3 levels)

　　• Self-diagnostic function and analog input disconnectiondetection assistance function (compliant to IEC60730)

　　• Input signal amplitude by the programmable gain amplifier(4 channels)

　　• Gain setting reference GND port: 2 ports

　　• ADC: 3-channel simultaneous sample-and-hold circuit (3shunt method), double data register (1 shunt method),amplifiers (4 channels), comparator (4 channels)

　　■ 8-bit D/A converter: 2 channels

　　• This can be used as reference voltage for a comparator

　　■ Register write protection function can protectvalues in important registers againstoverwriting.

　　■ Up to 111 pins for general I/O ports

　　• 5-V tolerant, open drain, input pull-up, switching ofdriving capacity

　　■ Operating temperature range

　　• −40 to +85 ℃

　　RX24U应用:

　　• General industrial and consumer equipment

　　RX24U主要指标:

　　图1.RX24U框图

　　RX24U开发板RSK

　　The Renesas Starter Kit for RX24U is the perfect starter kit for developers who are new to the RX24U.

　　The kit includes an LCD display module, on-chip debugging emulator, and integrated development environment so you can start evaluating the RX24U immediately after opening the box.

　　Please use this product to experience the performance and functions of the RX24U.

　　图2.RX24U开发板RSK外形图

　　RX24U开发板RSK主要特性:

　　Such as IIC and SCI the communication function can be evaluated.

　　In addition, CAN can be evaluated.

　　Including sample codes(Sample programs will be available in Renesas Web site.) Easy to understand coding technique.

　　Required IBM-PC compatible PC(need USB interface, Processor 1GHz over), OS: Windows 10/8/7/Vista(other than the listed OS is not supported)

　　RX24U开发板RSK主要指标:

　　图3.RX24U开发板RSK布局图

　　图4.RX24U开发板RSK正面元件布局图

　　图5.RX24U开发板RSK内部框图

　　图6.RX24U开发板RSK调试连接图

　　图7.RX24U开发板RSK电路图(1)

　　图8.RX24U开发板RSK电路图(2)

　　图9.RX24U开发板RSK电路图(3)

　　图10.RX24U开发板RSK电路图(4)

　　图11.RX24U开发板RSK电路图(5)

　　图12.RX24U开发板RSK电路图(6)

　　图13.RX24U开发板RSK电路图(7)

　　图14.RX24U开发板RSK电路图(8)

　　图15.RX24U开发板RSK电路图(9)

　　图16.RX24U开发板RSK电路图(10)

　　2010年4月1日，日本东京讯--在完成了对前株式会社瑞萨科技与NEC电子公司的业务整合工作后，新成立的瑞萨电子株式会社(以下简称瑞萨电子;TSE：6723)于2010年4月1日宣布公司正式启动商业运营。

　　同时，在当天进行的瑞萨电子董事会议上，已通过由山口纯史担任瑞萨电子董事会主席、赤尾泰担任总裁。瑞萨电子也宣布公司发行普通股股票给NEC电子公司(以下简称NEC电子;TSE：6701)、株式会社日立制作所(以下简称日立制作所;TSE: 6501 / NYSE: HIT)、三菱电机株式会社(以下简称三菱电机;TSE：6503)，以换取总计约1346亿日元的资金。

　　瑞萨电子通过集成了睿智新技术的专业优势，努力成为能帮助全社会实现愿景并构筑未来的企业，瑞萨电子致力于创建一个人与自然和谐相处、共同繁荣的世界。

　　瑞萨电子将在发挥创造力和技术创新能力的基础上，最迅速的响应世界各地客户的需求，并力争发展成为一个强大的、成长型半导体厂商和值得信任的商业合作伙伴。

　　为了支持新公司的企业理念与企业愿景，瑞萨电子将着重关注于包括MCU(微控制器)、SoC解决方案、模拟与电源器件在内的三大专业技术领域。公司将发挥合并后的联合优势，构筑一个更为强大的全新半导体公司，并在以不断提高收益，努力成为能够驾驭瞬息万变的半导体市场的“强大半导体企业”的同时，充分利用由新的运营而产生的资源，致力于进一步拓展全球市场业务。

　　详情请见:

r20ut3757eg0100-rskrx24u-schema.pdf

r20ut3758eg0100-rskrx24u-usermanual.pdf

r01ds0278ej0100-rx24u.pdf